Re: [SQU] WCCP w/bad rcvd_id

You've just compiled the module wrong.

I've turned the ip_wccp module into a patch that applies to kernel
2.2.18. This means you can select it at configure time for your kernel,
and the make file will compile it correctly for you.

http://www.swelltech.com/pengies/joe/patches/

It's the last link on the page, and works just fine for me (I use it to
build WCCP enabled kernel rpms).

Good luck.

Awie wrote:

> Joe,
>
> Perhaps this is another different question. However, I saw that you ask the
> ip_gre or ip_wccp module is working correctly or not. That is a very
> interesting issue for me.
>
> I downloaded ip_wccp.c from Squid FAQ. When compiled it, I got some problems
> (I captured the error message into text file) and ip_wccp.o was not created.
>
> After trying to downloaded ip_wccp.o from Al Blake's web site (our Linux
> version is same with his), and try to load (with modprobe) I got error
> message again that explain modprobe cannot locate ip_wccp.o. I am very
> curios about this problem.
>
> Best Regards,
>
> Awie
>
> ----- Original Message -----
> From: "Joe Cooper" <joe@swelltech.com>
> To: "vishwanath" <vish@gn.gtsl.co.in>
> Cc: <squid-users@ircache.net>
> Sent: Sunday, March 04, 2001 4:10 AM
> Subject: Re: [SQU] WCCP w/bad rcvd_id
>
>
>
>> If I recall correctly, this indicates that you may have conflicts with
>> multiple IPs on your Squid box.
>>
>> Have you tried configuring either the wccp_incoming, or wccp_outgoing
>> address (I don't remember which one of these fixed the problem for me in
>> the past--but I think one of them did)?
>>
>> Also, are you sure the ip_gre or ip_wccp module is working correctly and
>> unencapsulating the packets? While I've always been able to get both
>> working here in the office, in the field I've had some problems with the
>> patched ip_gre...and nothing I could do would make it work. Plugging
>> ip_wccp into the same configuration worked flawlessly first time.
>>
>> Hope this helps.
>>
>> vishwanath wrote:
>>
>>
>>> dear all
>>> please help me...
>>> i am trying to deploy squid 2.3STABLE4
>>> with WCCP
>>> i am using catalyst 6509 layer 3 switch IOS 12.1
>>>
>>> here is the output of wccp debug on catalyst
>>>
>>>
>>
> ============================================================================
>
>>> 6d23h: WCCP-EVNT: Here_I_Am packet from 206.102.1.100 w/bad rcvd_id
>>> 00000000
>>> 6d23h: WCCP-PKT: Sending I_See_You packet to 206.102.1.100 w/ rcvd_id
>>> 0000000F
>>> 6d23h: WCCP-EVNT: Here_I_Am packet from 206.102.1.100 w/bad rcvd_id
>>> 00000000
>>> 6d23h: WCCP-PKT: Sending I_See_You packet to 206.102.1.100 w/ rcvd_id
>>> 00000010
>>> 6d23h: %WCCP-5-CACHEFOUND: Web Cache 206.102.1.100 acquired
>>> 6d23h: WCCP-PKT: Sending I_See_You packet to 206.102.1.100 w/ rcvd_id
>>> 00000011
>>> 6d23h: WCCP-EVNT: Here_I_Am packet from 206.102.1.100 w/bad rcvd_id
>>> 00000000
>>> 6d23h: WCCP-PKT: Sending I_See_You packet to 206.102.1.100 w/ rcvd_id
>>> 00000012
>>> 6d23h: WCCP-EVNT: Here_I_Am packet from 206.102.1.100 w/bad rcvd_id
>>> 00000000
>>>
>>
> ============================================================================
>
>>>
>>> i have tried using
>>> wccp version 3 in squid instead of 4
>>>
>>> have configured the wccp_router correctly
>>>
>>> the setup works fine if i use route-map commands in switch
>>>
>>> thanx in advance
>>>
>>> vish
>>
>>
>> --
>> Joe Cooper <joe@swelltech.com>
>> Affordable Web Caching Proxy Appliances
>> http://www.swelltech.com
>>
>> --
>> To unsubscribe, see http://www.squid-cache.org/mailing-lists.html
>>
>
>
>
> --
> To unsubscribe, see http://www.squid-cache.org/mailing-lists.html

-- 
                                   --
                      Joe Cooper <joe@swelltech.com>
                  Affordable Web Caching Proxy Appliances
                         http://www.swelltech.com
--
To unsubscribe, see http://www.squid-cache.org/mailing-lists.html