Re: SNMP

O...ow....It cause me more confuse....

Please advise.

Thx

Best Regards,

Awie
awie@eksadata.com
PT. EKSADATA INTISOLUSI
Phone : (62-361) 261514
Mobile1 : (62-82) 3610369
Mobile2 : (62-818) 346241
----- Original Message -----
From: "Dan Williamson" <danw@norcomcable.ca>
To: "Squid-Users" <squid-users@ircache.net>
Sent: Sunday, October 22, 2000 10:01 PM
Subject: RE: SNMP

> No, its not correct. You should leave it at 0.0.0.0
>
> Check the FAQ's on the snmp section of Squid. In there there is info on
> gettings started, as well some other links with examples of how mrtg can
be
> used with Squid.
> http://www.squid-cache.org/Doc/FAQ/FAQ-18.html#ss18.8
>
> -----Original Message-----
> From: Awie [mailto:awie@eksadata.com]
> Sent: October 22, 2000 8:52 AM
> To: Henrik Nordstrom
> Cc: squid-users@ircache.net
> Subject: Re: SNMP
>
>
> Henrik,
>
> I just want to make sure. If my MRTG run in the box that using IP
> 202.90.140.36, then I should change the squid.conf to be:
>
> snmp_incoming_address 202.90.140.36
> #snmp_outgoing_address 0.0.0.0
>
> Is that correct?
>
> Please advise. Thx
>
> Best Regards,
>
> Awie
> awie@eksadata.com
> PT. EKSADATA INTISOLUSI
> Phone : (62-361) 261514
> Mobile1 : (62-82) 3610369
> Mobile2 : (62-818) 346241
> ----- Original Message -----
> From: "Henrik Nordstrom" <hno@hem.passagen.se>
> To: "Awie" <awie@eksadata.com>
> Cc: <squid-users@ircache.net>
> Sent: Sunday, October 22, 2000 5:52 PM
> Subject: Re: SNMP
>
>
> > Last time I looked cfgmaker could only handle routers.
> >
> > 0.0.0.0 is not an address.
> >
> > The note is confusing. It should read:
> >
> > Note: If you want both incoming and outgoing to be the same address then
> > leave snmp_outgoing_address at 0.0.0.0 and only set
> > snmp_incoming_address.
> >
> > --
> > Henrik Nordstrom
> > Squid hacker
> >
> >
> > Awie wrote:
> > >
> > > Henrik,
> > >
> > > Sorry to ask you more questions. I tried to monitor Squid with MRTG.
> > > However, I found that Squid not responding to cfgmaker of MRTG. Below
> > > my SNMP configuration:
> > >
> > > acl users src 202.91.140.0/255.255.255.192
> > > acl squidsnmp snmp_community squid
> > > #snmp_port 3401
> > > snmp_access allow snmpsquid users
> > > #snmp_incoming_address 0.0.0.0
> > > #snmp_outgoing_address 0.0.0.0
> > >
> > > The IP addr of Squid is different from IP addr of MRTG.
> > >
> > > Should I change the address of snmp incoming & outgoing ? I am afraid
> > > to change the address because I read a note in original squid.conf (as
> > > below):
> > >
> > > NOTE, snmp_incoming_address and snmp_outgoing_address can not have the
> > > same value since they both use port 3130.
> > >
> > > Please advise. Thx
> > >
> > > Best Regards,
> > >
> > > Awie
> > > awie@eksadata.com
> > > PT. EKSADATA INTISOLUSI
> > > Phone : (62-361) 261514
> > > Mobile1 : (62-82) 3610369
> > > Mobile2 : (62-818) 346241
> >
> > --
> > To unsubscribe, see http://www.squid-cache.org/mailing-lists.html
> >
>
> --
> To unsubscribe, see http://www.squid-cache.org/mailing-lists.html
>
> --
> To unsubscribe, see http://www.squid-cache.org/mailing-lists.html
>

--
To unsubscribe, see http://www.squid-cache.org/mailing-lists.html