RE: SNMP

No, its not correct. You should leave it at 0.0.0.0

Check the FAQ's on the snmp section of Squid. In there there is info on
gettings started, as well some other links with examples of how mrtg can be
used with Squid.
http://www.squid-cache.org/Doc/FAQ/FAQ-18.html#ss18.8

-----Original Message-----
From: Awie [mailto:awie@eksadata.com]
Sent: October 22, 2000 8:52 AM
To: Henrik Nordstrom
Cc: squid-users@ircache.net
Subject: Re: SNMP

Henrik,

I just want to make sure. If my MRTG run in the box that using IP
202.90.140.36, then I should change the squid.conf to be:

snmp_incoming_address 202.90.140.36
#snmp_outgoing_address 0.0.0.0

Is that correct?

Please advise. Thx

Best Regards,

Awie
awie@eksadata.com
PT. EKSADATA INTISOLUSI
Phone : (62-361) 261514
Mobile1 : (62-82) 3610369
Mobile2 : (62-818) 346241
----- Original Message -----
From: "Henrik Nordstrom" <hno@hem.passagen.se>
To: "Awie" <awie@eksadata.com>
Cc: <squid-users@ircache.net>
Sent: Sunday, October 22, 2000 5:52 PM
Subject: Re: SNMP

> Last time I looked cfgmaker could only handle routers.
>
> 0.0.0.0 is not an address.
>
> The note is confusing. It should read:
>
> Note: If you want both incoming and outgoing to be the same address then
> leave snmp_outgoing_address at 0.0.0.0 and only set
> snmp_incoming_address.
>
> --
> Henrik Nordstrom
> Squid hacker
>
>
> Awie wrote:
> >
> > Henrik,
> >
> > Sorry to ask you more questions. I tried to monitor Squid with MRTG.
> > However, I found that Squid not responding to cfgmaker of MRTG. Below
> > my SNMP configuration:
> >
> > acl users src 202.91.140.0/255.255.255.192
> > acl squidsnmp snmp_community squid
> > #snmp_port 3401
> > snmp_access allow snmpsquid users
> > #snmp_incoming_address 0.0.0.0
> > #snmp_outgoing_address 0.0.0.0
> >
> > The IP addr of Squid is different from IP addr of MRTG.
> >
> > Should I change the address of snmp incoming & outgoing ? I am afraid
> > to change the address because I read a note in original squid.conf (as
> > below):
> >
> > NOTE, snmp_incoming_address and snmp_outgoing_address can not have the
> > same value since they both use port 3130.
> >
> > Please advise. Thx
> >
> > Best Regards,
> >
> > Awie
> > awie@eksadata.com
> > PT. EKSADATA INTISOLUSI
> > Phone : (62-361) 261514
> > Mobile1 : (62-82) 3610369
> > Mobile2 : (62-818) 346241
>
> --
> To unsubscribe, see http://www.squid-cache.org/mailing-lists.html
>

--
To unsubscribe, see http://www.squid-cache.org/mailing-lists.html
--
To unsubscribe, see http://www.squid-cache.org/mailing-lists.html